Customize the docker0 bridge

The information in this section explains how to customize the Docker default bridge. This is a bridge network named bridge created automatically when you install Docker.

Note: The Docker networks feature allows you to create user-defined networks in addition to the default bridge network.

By default, the Docker server creates and configures the host system’s docker0 interface as an Ethernet bridge inside the Linux kernel that can pass packets back and forth between other physical or virtual network interfaces so that they behave as a single Ethernet network.

Docker configures docker0 with an IP address, netmask and IP allocation range. The host machine can both receive and send packets to containers connected to the bridge, and gives it an MTU – the maximum transmission unit or largest packet length that the interface will allow – of 1,500 bytes. These options are configurable at server startup:

  • --bip=CIDR – supply a specific IP address and netmask for the docker0 bridge, using standard CIDR notation like 192.168.1.5/24.

  • --fixed-cidr=CIDR – restrict the IP range from the docker0 subnet, using the standard CIDR notation like 172.16.1.0/28. This range must be an IPv4 range for fixed IPs (ex: 10.20.0.0/16) and must be a subset of the bridge IP range (docker0 or set using --bridge). For example with --fixed-cidr=192.168.1.0/25, IPs for your containers will be chosen from the first half of 192.168.1.0/24 subnet.

  • --mtu=BYTES – override the maximum packet length on docker0.

Once you have one or more containers up and running, you can confirm that Docker has properly connected them to the docker0 bridge by running the brctl command on the host machine and looking at the interfaces column of the output. Here is a host with two different containers connected:

# Display bridge info

$ sudo brctl show

bridge name     bridge id               STP enabled     interfaces
docker0         8000.3a1d7362b4ee       no              veth65f9
                                                        vethdda6

If the brctl command is not installed on your Docker host, then on Ubuntu you should be able to run sudo apt-get install bridge-utils to install it.

Finally, the docker0 Ethernet bridge settings are used every time you create a new container. Docker selects a free IP address from the range available on the bridge each time you docker run a new container, and configures the container’s eth0 interface with that IP address and the bridge’s netmask. The Docker host’s own IP address on the bridge is used as the default gateway by which each container reaches the rest of the Internet.

# The network, as seen from a container

$ docker run -i -t --rm base /bin/bash

root@f38c87f2a42d:/# ip addr show eth0

24: eth0: <BROADCAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    link/ether 32:6f:e0:35:57:91 brd ff:ff:ff:ff:ff:ff
    inet 172.17.0.3/16 scope global eth0
       valid_lft forever preferred_lft forever
    inet6 fe80::306f:e0ff:fe35:5791/64 scope link
       valid_lft forever preferred_lft forever

root@f38c87f2a42d:/# ip route

default via 172.17.42.1 dev eth0
172.17.0.0/16 dev eth0  proto kernel  scope link  src 172.17.0.3

root@f38c87f2a42d:/# exit

Remember that the Docker host will not be willing to forward container packets out on to the Internet unless its ip_forward system setting is 1 – see the section on Communicating to the outside world for details.

© 2017 Docker, Inc.
Licensed under the Apache License, Version 2.0.
Docker and the Docker logo are trademarks or registered trademarks of Docker, Inc. in the United States and/or other countries.
Docker, Inc. and other parties may also have trademark rights in other terms used herein.
https://docs.docker.com/v1.13/engine/userguide/networking/default_network/custom-docker0/