iosxr_interface – Manage Interface on Cisco IOS XR network devices

New in version 2.4.

Synopsis

  • This module provides declarative management of Interfaces on Cisco IOS XR network devices.

Requirements

The below requirements are needed on the host that executes this module.

  • ncclient >= 0.5.3 when using netconf
  • lxml >= 4.1.1 when using netconf

Parameters

Parameter Choices/Defaults Comments
active
-
added in 2.5
    Choices:
  • active
  • preconfigure
Whether the interface is active or preconfigured. Preconfiguration allows you to configure modular services cards before they are inserted into the router. When the cards are inserted, they are instantly configured. Active cards are the ones already inserted.
aggregate
-
List of Interface definitions. Include multiple interface configurations together, one each on a separate line
delay
-
Default:
10
Time in seconds to wait before checking for the operational state on remote device. This wait is applicable for operational state argument which are state with values up/down, tx_rate and rx_rate.
description
-
Description of Interface being configured.
duplex
-
    Choices:
  • full
  • half
Configures the interface duplex mode. Default is auto-negotiation when not configured.
enabled
boolean
    Choices:
  • no
  • yes
Removes the shutdown configuration, which removes the forced administrative down on the interface, enabling it to move to an up or down state.
mtu
-
Sets the MTU value for the interface. Range is between 64 and 65535'
name
- / required
Name of the interface to configure in type + path format. e.g. GigabitEthernet0/0/0/0
provider
dictionary
Deprecated
Starting with Ansible 2.5 we recommend using connection: network_cli.
For more information please see the Network Guide.
A dict object containing connection details.
host
string / required
Specifies the DNS host name or address for connecting to the remote device over the specified transport. The value of host is used as the destination address for the transport.
password
string
Specifies the password to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_PASSWORD will be used instead.
port
integer
Default:
22
Specifies the port to use when building the connection to the remote device.
ssh_keyfile
path
Specifies the SSH key to use to authenticate the connection to the remote device. This value is the path to the key used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_SSH_KEYFILE will be used instead.
timeout
integer
Default:
10
Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error.
username
string
Configures the username to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_USERNAME will be used instead.
rx_rate
-
Receiver rate in bits per second (bps).
This is state check parameter only.
Supports conditionals, see Conditionals in Networking Modules
speed
-
    Choices:
  • 10
  • 100
  • 1000
Configure the speed for an interface. Default is auto-negotiation when not configured.
state
-
    Choices:
  • present
  • absent
  • up
  • down
State of the Interface configuration, up means present and operationally up and down means present and operationally down
tx_rate
-
Transmit rate in bits per second (bps).
This is state check parameter only.
Supports conditionals, see Conditionals in Networking Modules

Notes

Note

  • Tested against IOS XRv 6.1.2
  • Preconfiguration of physical interfaces is not supported with netconf transport.
  • For more information on using Ansible to manage network devices see the Ansible Network Guide
  • For more information on using Ansible to manage Cisco devices see the Cisco integration page.

Examples

- name: configure interface
  iosxr_interface:
      name: GigabitEthernet0/0/0/2
      description: test-interface
      speed: 100
      duplex: half
      mtu: 512

- name: remove interface
  iosxr_interface:
    name: GigabitEthernet0/0/0/2
    state: absent

- name: make interface up
  iosxr_interface:
    name: GigabitEthernet0/0/0/2
    enabled: True

- name: make interface down
  iosxr_interface:
    name: GigabitEthernet0/0/0/2
    enabled: False

- name: Create interface using aggregate
  iosxr_interface:
    aggregate:
    - name: GigabitEthernet0/0/0/3
    - name: GigabitEthernet0/0/0/2
    speed: 100
    duplex: full
    mtu: 512
    state: present

- name: Create interface using aggregate along with additional params in aggregate
  iosxr_interface:
    aggregate:
    - { name: GigabitEthernet0/0/0/3, description: test-interface 3 }
    - { name: GigabitEthernet0/0/0/2, description: test-interface 2 }
    speed: 100
    duplex: full
    mtu: 512
    state: present

- name: Delete interface using aggregate
  iosxr_interface:
    aggregate:
    - name: GigabitEthernet0/0/0/3
    - name: GigabitEthernet0/0/0/2
    state: absent

- name: Check intent arguments
  iosxr_interface:
    name: GigabitEthernet0/0/0/5
    state: up
    delay: 20

- name: Config + intent
  iosxr_interface:
    name: GigabitEthernet0/0/0/5
    enabled: False
    state: down
    delay: 20

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key Returned Description
commands
list
always (empty list when no commands to send)
The list of configuration mode commands sent to device with transport cli

Sample:
['interface GigabitEthernet0/0/0/2', 'description test-interface', 'duplex half', 'mtu 512']
xml
list
added in 2.5
always (empty list when no xml rpc to send)
NetConf rpc xml sent to device with transport netconf

Sample:
['<config xmlns:xc="urn:ietf:params:xml:ns:netconf:base:1.0"> <interface-configurations xmlns="http://cisco.com/ns/yang/Cisco-IOS-XR-ifmgr-cfg"> <interface-configuration xc:operation="merge"> <active>act</active> <interface-name>GigabitEthernet0/0/0/0</interface-name> <description>test-interface-0</description> <mtus><mtu> <owner>GigabitEthernet</owner> <mtu>512</mtu> </mtu></mtus> <ethernet xmlns="http://cisco.com/ns/yang/Cisco-IOS-XR-drivers-media-eth-cfg"> <speed>100</speed> <duplex>half</duplex> </ethernet> </interface-configuration> </interface-configurations></config>']


Status

Red Hat Support

More information about Red Hat’s support of this module is available from this Red Hat Knowledge Base article.

Authors

  • Ganesh Nalawade (@ganeshrn)
  • Kedar Kekan (@kedarX)

Hint

If you notice any issues in this documentation you can edit this document to improve it.

© 2012–2018 Michael DeHaan
© 2018–2019 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/2.8/modules/iosxr_interface_module.html