community.network.icx_interface – Manage Interface on Ruckus ICX 7000 series switches

Note

This plugin is part of the community.network collection (version 3.0.0).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install community.network.

To use it in a playbook, specify: community.network.icx_interface.

Synopsis

  • This module provides declarative management of Interfaces on ruckus icx devices.

Parameters

Parameter Choices/Defaults Comments
aggregate
list / elements=string
List of Interfaces definitions.
check_running_config
boolean
    Choices:
  • no
  • yes
Check running configuration. This can be set as environment variable.
Module will use environment variable value(default:True), unless it is overridden, by specifying it as module parameter.
delay
integer
Time in seconds to wait before checking for the operational state on remote device. This wait is applicable for operational state argument which are state with values up/down, tx_rate and rx_rate.
description
string
Name of the description.
enabled
boolean
    Choices:
  • no
  • yes
Interface link status
name
string
Name of the Interface.
neighbors
list / elements=string
Check the operational state of given interface name for CDP/LLDP neighbor.
The following suboptions are available.
host
string
CDP/LLDP neighbor host for given interface name.
port
string
CDP/LLDP neighbor port to which given interface name is connected.
power
dictionary
Inline power on Power over Ethernet (PoE) ports.
by_class
string
    Choices:
  • 0
  • 1
  • 2
  • 3
  • 4
The range is 0-4
The power limit based on class value for given interface name
enabled
boolean
    Choices:
  • no
  • yes
enable/disable the poe of the given interface name
limit
string
The range is 1000-15400|30000mW. For PoH ports the range is 1000-95000mW
The power limit based on actual power value for given interface name
priority
string
    Choices:
  • 1
  • 2
  • 3
The range is 1 (highest) to 3 (lowest)
The priority for power management or given interface name
rx_rate
string
Receiver rate in bits per second (bps).
This is state check parameter only.
Supports conditionals, see Conditionals in Networking Modules
speed
string
    Choices:
  • 10-full
  • 10-half
  • 100-full
  • 100-half
  • 1000-full
  • 1000-full-master
  • 1000-full-slave
  • 10g-full
  • 10g-full-master
  • 10g-full-slave
  • 2500-full
  • 2500-full-master
  • 2500-full-slave
  • 5g-full
  • 5g-full-master
  • 5g-full-slave
  • auto
Interface link speed/duplex
state
string
    Choices:
  • present
  • absent
  • up
  • down
State of the Interface configuration, up means present and operationally up and down means present and operationally down
stp
boolean
    Choices:
  • no
  • yes
enable/disable stp for the interface
tx_rate
string
Transmit rate in bits per second (bps).
This is state check parameter only.
Supports conditionals, see Conditionals in Networking Modules
check_running_config
boolean
    Choices:
  • no
  • yes
Check running configuration. This can be set as environment variable.
Module will use environment variable value(default:True), unless it is overridden, by specifying it as module parameter.
delay
integer
Default:
10
Time in seconds to wait before checking for the operational state on remote device. This wait is applicable for operational state argument which are state with values up/down, tx_rate and rx_rate.
description
string
Name of the description.
enabled
boolean
    Choices:
  • no
  • yes
Interface link status
name
string
Name of the Interface.
neighbors
list / elements=string
Check the operational state of given interface name for CDP/LLDP neighbor.
The following suboptions are available.
host
string
CDP/LLDP neighbor host for given interface name.
port
string
CDP/LLDP neighbor port to which given interface name is connected.
power
dictionary
Inline power on Power over Ethernet (PoE) ports.
by_class
string
    Choices:
  • 0
  • 1
  • 2
  • 3
  • 4
The range is 0-4
The power limit based on class value for given interface name
enabled
boolean
    Choices:
  • no
  • yes
enable/disable the poe of the given interface name
Default is false.
limit
string
The range is 1000-15400|30000mW. For PoH ports the range is 1000-95000mW
The power limit based on actual power value for given interface name
priority
string
    Choices:
  • 1
  • 2
  • 3
The range is 1 (highest) to 3 (lowest)
The priority for power management or given interface name
rx_rate
string
Receiver rate in bits per second (bps).
This is state check parameter only.
Supports conditionals, see Conditionals in Networking Modules
speed
string
    Choices:
  • 10-full
  • 10-half
  • 100-full
  • 100-half
  • 1000-full
  • 1000-full-master
  • 1000-full-slave
  • 10g-full
  • 10g-full-master
  • 10g-full-slave
  • 2500-full
  • 2500-full-master
  • 2500-full-slave
  • 5g-full
  • 5g-full-master
  • 5g-full-slave
  • auto
Interface link speed/duplex
state
string
    Choices:
  • present
  • absent
  • up
  • down
State of the Interface configuration, up means present and operationally up and down means present and operationally down
stp
boolean
    Choices:
  • no
  • yes
enable/disable stp for the interface
tx_rate
string
Transmit rate in bits per second (bps).
This is state check parameter only.
Supports conditionals, see Conditionals in Networking Modules

Notes

Note

Examples

- name: Enable ethernet port and set name
  community.network.icx_interface:
    name: ethernet 1/1/1
    description: interface-1
    stp: true
    enabled: true

- name: Disable ethernet port 1/1/1
  community.network.icx_interface:
      name: ethernet 1/1/1
      enabled: false

- name: Enable ethernet port range, set name and speed
  community.network.icx_interface:
      name: ethernet 1/1/1 to 1/1/10
      description: interface-1
      speed: 100-full
      enabled: true

- name: Enable poe. Set class
  community.network.icx_interface:
      name: ethernet 1/1/1
      power:
       by_class: 2

- name: Configure poe limit of interface
  community.network.icx_interface:
      name: ethernet 1/1/1
      power:
       limit: 10000

- name: Disable poe of interface
  community.network.icx_interface:
      name: ethernet 1/1/1
      power:
       enabled: false

- name: Set lag name for a range of lags
  community.network.icx_interface:
      name: lag 1 to 10
      description: test lags

- name: Disable lag
  community.network.icx_interface:
      name: lag 1
      enabled: false

- name: Enable management interface
  community.network.icx_interface:
      name: management 1
      enabled: true

- name: Enable loopback interface
  community.network.icx_interface:
      name: loopback 10
      enabled: true

- name: Add interface using aggregate
  community.network.icx_interface:
      aggregate:
      - { name: ethernet 1/1/1, description: test-interface-1, power: { by_class: 2 } }
      - { name: ethernet 1/1/3, description: test-interface-3}
      speed: 10-full
      enabled: true

- name: Check tx_rate, rx_rate intent arguments
  community.network.icx_interface:
    name: ethernet 1/1/10
    state: up
    tx_rate: ge(0)
    rx_rate: le(0)

- name: Check neighbors intent arguments
  community.network.icx_interface:
    name: ethernet 1/1/10
    neighbors:
    - port: 1/1/5
      host: netdev

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key Returned Description
commands
list / elements=string
always
The list of configuration mode commands to send to the device.

Sample:
['interface ethernet 1/1/1', 'port-name interface-1', 'state present', 'speed-duplex 100-full', 'inline power priority 1']


Authors

  • Ruckus Wireless (@Commscope)

© 2012–2018 Michael DeHaan
© 2018–2021 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/latest/collections/community/network/icx_interface_module.html