junipernetworks.junos.junos_l2_interfaces – L2 interfaces resource module

Note

This plugin is part of the junipernetworks.junos collection (version 2.6.0).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install junipernetworks.junos.

To use it in a playbook, specify: junipernetworks.junos.junos_l2_interfaces.

New in version 1.0.0: of junipernetworks.junos

Synopsis

  • This module provides declarative management of a Layer-2 interface on Juniper JUNOS devices.

Note

This module has a corresponding action plugin.

Requirements

The below requirements are needed on the host that executes this module.

  • ncclient (>=v0.6.4)

Parameters

Parameter Choices/Defaults Comments
config
list / elements=dictionary
A dictionary of Layer-2 interface options
access
dictionary
Configure the interface as a Layer 2 access mode.
vlan
string
Configure the access VLAN ID.
enhanced_layer
boolean
    Choices:
  • no
  • yes
True if your device has Enhanced Layer 2 Software (ELS). If the l2 configuration is under interface-mode the value is True else if the l2 configuration is under port-mode value is False
name
string / required
Full name of interface, e.g. ge-0/0/1.
trunk
dictionary
Configure the interface as a Layer 2 trunk mode.
allowed_vlans
list / elements=string
List of VLANs to be configured in trunk port. It's used as the VLAN range to ADD or REMOVE from the trunk.
native_vlan
string
Native VLAN to be configured in trunk port. It is used as the trunk native VLAN ID.
unit
integer
Logical interface number. Value of unit should be of type integer.
running_config
string
This option is used only with state parsed.
The value of this option should be the output received from the Junos device by executing the command show interfaces.
The state parsed reads the configuration from running_config option and transforms it into Ansible structured data as per the resource module's argspec and the value is then returned in the parsed key within the result.
state
string
    Choices:
  • merged
  • replaced
  • overridden
  • deleted
  • gathered
  • parsed
  • rendered
The state of the configuration after module completion

Notes

Note

  • This module requires the netconf system service be enabled on the remote device being managed.
  • Tested against vSRX JUNOS version 18.4R1.
  • This module works with connection netconf. See the Junos OS Platform Options.

Examples

# Using deleted

# Before state:
# -------------
#
# ansible@junos01# show interfaces
# ge-0/0/1 {
#    description "L2 interface";
#    speed 1g;
#    unit 0 {
#        family ethernet-switching {
#            interface-mode access;
#            vlan {
#                members vlan30;
#            }
#        }
#    }
#}
#ge-0/0/2 {
#    description "non L2 interface";
#    unit 0 {
#        family inet {
#            address 192.168.56.14/24;
#        }
#    }

- name: "Delete L2 attributes of given interfaces (Note: This won't delete the
    interface itself)."
  junipernetworks.junos.junos_l2_interfaces:
    config:
    - name: ge-0/0/1
    - name: ge-0/0/2
    state: deleted

# After state:
# ------------
#
# ansible@junos01# show interfaces
# ge-0/0/1 {
#    description "L2 interface";
#    speed 1g;
# }
#ge-0/0/2 {
#    description "non L2 interface";
#    unit 0 {
#        family inet {
#            address 192.168.56.14/24;
#        }
#    }


# Using merged

# Before state:
# -------------
# ansible@junos01# show interfaces
# ge-0/0/3 {
#    description "test interface";
#    speed 1g;
#}
# ge-0/0/4 {
#    description interface-trunk;
#    native-vlan-id 100;
#    unit 0 {
#        family ethernet-switching {
#            interface-mode trunk;
#            vlan {
#                members [ vlan40 ];
#            }
#        }
#    }
# }

- name: Merge provided configuration with device configuration (default operation
    is merge)
  junipernetworks.junos.junos_l2_interfaces:
    config:
    - name: ge-0/0/3
      access:
        vlan: v101
    - name: ge-0/0/4
      trunk:
        allowed_vlans:
        - vlan30
        native_vlan: 50
    state: merged

# After state:
# ------------
# user@junos01# show interfaces
# ge-0/0/3 {
#    description "test interface";
#    speed 1g;
#    unit 0 {
#        family ethernet-switching {
#            interface-mode access;
#            vlan {
#                members v101;
#            }
#        }
#    }
# }
# ge-0/0/4 {
#    description interface-trunk;
#    native-vlan-id 50;
#    unit 0 {
#        family ethernet-switching {
#            interface-mode trunk;
#            vlan {
#                members [ vlan40 vlan30 ];
#            }
#        }
#    }
# }


# Using overridden

# Before state:
# -------------
# ansible@junos01# show interfaces
# ge-0/0/3 {
#    description "test interface";
#    speed 1g;
#}
# ge-0/0/4 {
#    description interface-trunk;
#    native-vlan-id 100;
#    unit 0 {
#        family ethernet-switching {
#            interface-mode trunk;
#            vlan {
#                members [ vlan40 ];
#            }
#        }
#    }
# }
# ge-0/0/5 {
#    description "Configured by Ansible-11";
#    unit 0 {
#        family ethernet-switching {
#            interface-mode access;
#            vlan {
#                members v101;
#            }
#        }
#    }
# }

- name: Override provided configuration with device configuration
  junipernetworks.junos.junos_l2_interfaces:
    config:
    - name: ge-0/0/3
      access:
        vlan: v101
    - name: ge-0/0/4
      trunk:
        allowed_vlans:
        - vlan30
        native_vlan: 50
    state: overridden

# After state:
# ------------
# user@junos01# show interfaces
# ge-0/0/3 {
#    unit 0 {
#        family ethernet-switching {
#            interface-mode access;
#            vlan {
#                members v101;
#            }
#        }
#    }
# }
# ge-0/0/4 {
#    description interface-trunk;
#    native-vlan-id 50;
#    unit 0 {
#        family ethernet-switching {
#            interface-mode trunk;
#            vlan {
#                members [ vlan30 ];
#            }
#        }
#    }
# }


# Using replaced

# Before state:
# -------------
# ansible@junos01# show interfaces
# ge-0/0/3 {
#    description "test interface";
#    speed 1g;
#}
# ge-0/0/4 {
#    description interface-trunk;
#    native-vlan-id 100;
#    unit 0 {
#        family ethernet-switching {
#            interface-mode trunk;
#            vlan {
#                members [ vlan40 ];
#            }
#        }
#    }
# }

- name: Replace provided configuration with device configuration
  junipernetworks.junos.junos_l2_interfaces:
    config:
    - name: ge-0/0/3
      access:
        vlan: v101
    - name: ge-0/0/4
      trunk:
        allowed_vlans:
        - vlan30
        native_vlan: 50
    state: replaced

# After state:
# ------------
# user@junos01# show interfaces
# ge-0/0/3 {
#    unit 0 {
#        family ethernet-switching {
#            interface-mode access;
#            vlan {
#                members v101;
#            }
#        }
#    }
# }
# ge-0/0/4 {
#    description interface-trunk;
#    native-vlan-id 50;
#    unit 0 {
#        family ethernet-switching {
#            interface-mode trunk;
#            vlan {
#                members [ vlan30 ];
#            }
#        }
#    }
# }
# Using gathered
# Before state:
# ------------
#
# user@junos01# show interfaces
# ge-0/0/1 {
#     description "Configured by Ansible";
#     disable;
#     speed 100m;
#     mtu 1024;
#     hold-time up 2000 down 2200;
#     link-mode full-duplex;
#     unit 0 {
#         family ethernet-switching {
#             interface-mode access;
#             vlan {
#                 members vlan100;
#             }
#         }
#     }
# }
# ge-0/0/2 {
#     description "Configured by Ansible";
#     native-vlan-id 400;
#     speed 10m;
#     mtu 2048;
#     hold-time up 3000 down 3200;
#     unit 0 {
#         family ethernet-switching {
#             interface-mode trunk;
#             vlan {
#                 members [ vlan200 vlan300 ];
#             }
#         }
#     }
# }
# em1 {
#     description TEST;
# }
# fxp0 {
#     description ANSIBLE;
#     speed 1g;
#     link-mode automatic;
#     unit 0 {
#         family inet {
#             address 10.8.38.38/24;
#         }
#     }
# }
- name: Gather junos layer 2 interfaces as in given arguments
  junipernetworks.junos.junos_l2_interfaces:
    state: gathered
# Task Output (redacted)
# -----------------------
#
# "gathered": [
#         {
#             "access": {
#                 "vlan": "vlan100"
#             },
#             "enhanced_layer": true,
#             "name": "ge-0/0/1",
#             "unit": 0
#         },
#         {
#             "enhanced_layer": true,
#             "name": "ge-0/0/2",
#             "trunk": {
#                 "allowed_vlans": [
#                     "vlan200",
#                     "vlan300"
#                 ],
#                 "native_vlan": "400"
#             },
#             "unit": 0
#         }
#     ]
# After state:
# ------------
#
# user@junos01# show interfaces
# ge-0/0/1 {
#     description "Configured by Ansible";
#     disable;
#     speed 100m;
#     mtu 1024;
#     hold-time up 2000 down 2200;
#     link-mode full-duplex;
#     unit 0 {
#         family ethernet-switching {
#             interface-mode access;
#             vlan {
#                 members vlan100;
#             }
#         }
#     }
# }
# ge-0/0/2 {
#     description "Configured by Ansible";
#     native-vlan-id 400;
#     speed 10m;
#     mtu 2048;
#     hold-time up 3000 down 3200;
#     unit 0 {
#         family ethernet-switching {
#             interface-mode trunk;
#             vlan {
#                 members [ vlan200 vlan300 ];
#             }
#         }
#     }
# }
# em1 {
#     description TEST;
# }
# fxp0 {
#     description ANSIBLE;
#     speed 1g;
#     link-mode automatic;
#     unit 0 {
#         family inet {
#             address 10.8.38.38/24;
#         }
#     }
# }
# Using parsed
# parsed.cfg
# ------------
#
# <?xml version="1.0" encoding="UTF-8"?>
# <rpc-reply message-id="urn:uuid:0cadb4e8-5bba-47f4-986e-72906227007f">
#     <configuration changed-seconds="1590139550" changed-localtime="2020-05-22 09:25:50 UTC">
#         <interfaces>
#             <interface>
#                 <name>ge-0/0/1</name>
#                 <description>Configured by Ansible</description>
#                 <disable/>
#                 <speed>100m</speed>
#                 <mtu>1024</mtu>
#                 <hold-time>
#                     <up>2000</up>
#                     <down>2200</down>
#                 </hold-time>
#                 <link-mode>full-duplex</link-mode>
#                 <unit>
#                     <name>0</name>
#                     <family>
#                         <ethernet-switching>
#                             <interface-mode>access</interface-mode>
#                             <vlan>
#                                 <members>vlan100</members>
#                             </vlan>
#                         </ethernet-switching>
#                     </family>
#                 </unit>
#             </interface>
#         </interfaces>
#     </configuration>
# </rpc-reply>
# - name: Convert interfaces config to argspec without connecting to the appliance
#   junipernetworks.junos.junos_l2_interfaces:
#     running_config: "{{ lookup('file', './parsed.cfg') }}"
#     state: parsed
# Task Output (redacted)
# -----------------------
# "parsed": [
#         {
#             "access": {
#                 "vlan": "vlan100"
#             },
#             "enhanced_layer": true,
#             "name": "ge-0/0/1",
#             "unit": 0
#         },
#         {
#             "enhanced_layer": true,
#             "name": "ge-0/0/2",
#             "trunk": {
#                 "allowed_vlans": [
#                     "vlan200",
#                     "vlan300"
#                 ],
#                 "native_vlan": "400"
#             },
#             "unit": 0
#         }
#     ]
#
# Using rendered
- name: Render platform specific xml from task input using rendered state
  junipernetworks.junos.junos_l2_interfaces:
    config:
      - name: ge-0/0/1
        access:
          vlan: vlan100
      - name: ge-0/0/2
        trunk:
          allowed_vlans:
            - vlan200
            - vlan300
          native_vlan: '400'
    state: rendered
# Task Output (redacted)
# -----------------------
# "rendered": "<nc:interfaces
#     xmlns:nc="urn:ietf:params:xml:ns:netconf:base:1.0">
#     <nc:interface>
#         <nc:name>ge-0/0/1</nc:name>
#         <nc:unit>
#             <nc:name>0</nc:name>
#             <nc:family>
#                 <nc:ethernet-switching>
#                     <nc:interface-mode>access</nc:interface-mode>
#                     <nc:vlan>
#                         <nc:members>vlan100</nc:members>
#                     </nc:vlan>
#                 </nc:ethernet-switching>
#             </nc:family>
#         </nc:unit>
#     </nc:interface>
#     <nc:interface>
#         <nc:name>ge-0/0/2</nc:name>
#         <nc:unit>
#             <nc:name>0</nc:name>
#             <nc:family>
#                 <nc:ethernet-switching>
#                     <nc:interface-mode>trunk</nc:interface-mode>
#                     <nc:vlan>
#                         <nc:members>vlan200</nc:members>
#                         <nc:members>vlan300</nc:members>
#                     </nc:vlan>
#                 </nc:ethernet-switching>
#             </nc:family>
#         </nc:unit>
#         <nc:native-vlan-id>400</nc:native-vlan-id>
#     </nc:interface>
# </nc:interfaces>"

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key Returned Description
after
list / elements=string
when changed
The configuration as structured data after module completion.

Sample:
The configuration returned will always be in the same format of the parameters above.
before
list / elements=string
always
The configuration as structured data prior to module invocation.

Sample:
The configuration returned will always be in the same format of the parameters above.
commands
list / elements=string
always
The set of commands pushed to the remote device.

Sample:
['<nc:interfaces xmlns:nc="urn:ietf:params:xml:ns:netconf:base:1.0"> <nc:interface> <nc:name>ge-0/0/1</nc:name> <nc:unit> <nc:name>0</nc:name> <nc:family> <nc:ethernet-switching> <nc:interface-mode>access</nc:interface-mode> <nc:vlan> <nc:members>vlan100</nc:members> </nc:vlan> </nc:ethernet-switching> </nc:family> </nc:unit> </nc:interface> <nc:interface> <nc:name>ge-0/0/2</nc:name> <nc:unit> <nc:name>0</nc:name> <nc:family> <nc:ethernet-switching> <nc:interface-mode>trunk</nc:interface-mode> <nc:vlan> <nc:members>vlan200</nc:members> <nc:members>vlan300</nc:members> </nc:vlan> </nc:ethernet-switching> </nc:family> </nc:unit> <nc:native-vlan-id>400</nc:native-vlan-id> </nc:interface> </nc:interfaces>', 'xml 2', 'xml 3']


Authors

  • Ganesh Nalawade (@ganeshrn)

© 2012–2018 Michael DeHaan
© 2018–2021 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/latest/collections/junipernetworks/junos/junos_l2_interfaces_module.html